收藏本站
73
AT89C51ID2
4289C–8051–11/05
and RAM contents are preserved. The status of the Port pins during Power-Down mode
is detailed in Table 57.
Note:
VCC may be reduced to as low as V
RET during Power-Down mode to further reduce
power dissipation. Take care, however, that VDD is not reduced until Power-Down mode
is invoked.
Entering Power-Down Mode
To enter Power-Down mode, set PD bit in PCON register. The AT89C51ID2 enters the
Power-Down mode upon execution of the instruction that sets PD bit. The instruction
that sets PD bit is the last instruction executed.
Exiting Power-Down Mode
Note:
If VCC was reduced during the Power-Down mode, do not exit Power-Down mode until
VCC is restored to the normal operating level.
There are two ways to exit the Power-Down mode:
1.
Generate an enabled external interrupt.
–
The AT89C51ID2 provides capability to exit from Power-Down using INT0#,
INT1#.
Hardware clears PD bit in PCON register which starts the oscillator and
restores the clocks to the CPU and peripherals. Using INTx# input,
execution resumes when the input is released (see Figure 26). Execution
resumes with the interrupt service routine. Upon completion of the interrupt
service routine, program execution resumes with the instruction immediately
following the instruction that activated Power-Down mode.
Note:
The external interrupt used to exit Power-Down mode must be configured as level sensi-
tive (INT0# and INT1#) and must be assigned the highest priority. In addition, the
duration of the interrupt must be long enough to allow the oscillator to stabilize. The exe-
cution will only resume when the interrupt is deasserted.
Note:
Exit from power-down by external interrupt does not affect the SFRs nor the internal RAM
content.
Figure 26. Power-Down Exit Waveform Using INT1:0#
2.
Generate a reset.
–
A logic high on the RST pin clears PD bit in PCON register directly and
asynchronously. This starts the oscillator and restores the clock to the CPU
and peripherals. Program execution momentarily resumes with the
instruction immediately following the instruction that activated Power-Down
mode and may continue for a number of clock cycles before the internal
reset algorithm takes control. Reset initializes the AT89C51ID2 and vectors
the CPU to address 0000h.
Note:
During the time that execution resumes, the internal RAM cannot be accessed; however,
it is possible for the Port pins to be accessed. To avoid unexpected outputs at the Port
INT1:0#
OSC
Power-down phase
Oscillator restart phase
Active phase
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
AT89C51RC-24PU IC MCU 32K FLASH 24MHZ 40-DIP
AT89C51RC2-RLRIL IC MCU FLASH 8051 32K 3V 44-VQFP
AT89C51RE2-SLRUM MCU 8051 128K FLASH 44-PLCC
AT89C51SND1C-7HTUL IC MCU 64KB FLASH MEM 81-CBGA
AT89C51SND2C-7FTUL IC 8051 MCU FLASH 64K MP3 100BGA
AT89C52-24PI IC MICRO CTRL 24MHZ 40DIP
AT89C55WD-24AU IC 8051 MCU FLASH 20K 44TQFP
AT89EB5114-TGSIL IC 8051 MCU FLASH 4K 20SOIC
相关代理商/技术参数
AT89C51ID2-RLRUM 功能描述:8位微控制器 -MCU C51ID2 64K FLASH 32KHz 3-5.5V RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
AT89C51ID2-RLTIM 功能描述:IC 8051 MCU FLASH 64K 44VQFP RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:89C 标准包装:9 系列:87C 核心处理器:8051 芯体尺寸:8-位 速度:40/20MHz 连通性:UART/USART 外围设备:POR，WDT 输入/输出数:32 程序存储器容量:32KB（32K x 8） 程序存储器类型:OTP EEPROM 大小:- RAM 容量:256 x 8 电压 - 电源 (Vcc/Vdd):4.5 V ~ 5.5 V 数据转换器:- 振荡器型:内部 工作温度:0°C ~ 70°C 封装/外壳:40-DIP（0.600"，15.24mm） 包装:管件
AT89C51ID2-RLTUM 功能描述:8位微控制器 -MCU C51ID2 64K FLASH 32KHz 3-5.5V RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
AT89C51ID2-SLRIM 功能描述:IC MCU FLASH 8051 64K 5V 44-PLCC RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:89C 标准包装:1,500 系列:AVR® ATtiny 核心处理器:AVR 芯体尺寸:8-位 速度:16MHz 连通性:I²C，LIN，SPI，UART/USART，USI 外围设备:欠压检测/复位，POR，PWM，温度传感器，WDT 输入/输出数:16 程序存储器容量:8KB（4K x 16） 程序存储器类型:闪存 EEPROM 大小:512 x 8 RAM 容量:512 x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 5.5 V 数据转换器:A/D 11x10b 振荡器型:内部 工作温度:-40°C ~ 125°C 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 包装:带卷 (TR)
AT89C51ID2-SLRUM 功能描述:8位微控制器 -MCU C51ID2 64K FLASH TWI 32KHz 5V RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
AT89C51ID2-SLSIM 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-bit Flash Microcontroller
AT89C51ID2-SLSUM 功能描述:8位微控制器 -MCU 64K FLASH 32KHz 3.5-5V Ind. RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
AT89C51ID2-SMSIM 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-bit Flash Microcontroller